M1A bolt holdback issue

M14s, M1 Garands & Carbines, Enfields, M1903s
Post Reply
hurricanecharlie
Executive Member
Executive Member
Posts: 676
Joined: Mon Jan 18, 2010 7:27 pm
Location: broward county

M1A bolt holdback issue

Post by hurricanecharlie » Mon Jan 01, 2018 3:06 pm

Put in new bolt catch.
bolt initially hold by applying bolt catch with no mag.
then lets go with slightest jarring>
Could this be op rod spring issue?
Also ,bought a pro mag ten round mag.
Will not strip the round to feed.
Is this typical of pro mag product?

User avatar
Dave P
Life Member
Life Member
Posts: 2489
Joined: Tue Apr 20, 2004 11:29 am
Location: west of Lake City

Re: M1A bolt holdback issue

Post by Dave P » Mon Jan 01, 2018 5:33 pm

What was wrong with original bolt catch?? I am sure the angles of the dangles on the catch are very important to proper operation. Have you got a USGI catch?

And, be VERY CAREFUL dinking with its pivot pin. Easy to break the rcvr.

I recall that promag magazines are not so good. Find some real USGI ones.
Go Trump!

User avatar
M14man
Life Member
Life Member
Posts: 1764
Joined: Mon Sep 05, 2005 7:23 pm
Location: Near Brooksville

Re: M1A bolt holdback issue

Post by M14man » Wed Jan 03, 2018 10:45 pm

I had the same issue. Seems like the catch just makes the grab. Had Dow's put in a new one. Months later it was slipping too. I had heard there was an after market longer one. Not sure if a skilled Tig man could extend the leg out also.(obviously out of gun)Mine would lock up, but soon as I removed the mag it would slip, or if it held; when bumped

hurricanecharlie
Executive Member
Executive Member
Posts: 676
Joined: Mon Jan 18, 2010 7:27 pm
Location: broward county

Re: M1A bolt holdback issue

Post by hurricanecharlie » Wed Jan 03, 2018 11:13 pm

Exactly what I am having.
who makes extended bolt catch?

User avatar
M14man
Life Member
Life Member
Posts: 1764
Joined: Mon Sep 05, 2005 7:23 pm
Location: Near Brooksville

Re: M1A bolt holdback issue

Post by M14man » Wed Jan 03, 2018 11:30 pm

It was maybe 8 0r 9 years ago that I saw it advertised. Possibly a internet search will turn up, or a call to Fulton or SPringfield.
I just live with the issue and lower the bolt so it doesn't slip.I don't like it when I am at a range and they call "safe", and have to lock it back and remove mag. I use a chamber flag then. As said, maybe a skilled welder could add a little more leg to a part.

User avatar
M14man
Life Member
Life Member
Posts: 1764
Joined: Mon Sep 05, 2005 7:23 pm
Location: Near Brooksville

Re: M1A bolt holdback issue

Post by M14man » Wed Jan 03, 2018 11:40 pm


User avatar
flcracker
Life Member
Life Member
Posts: 5575
Joined: Thu Sep 23, 2004 8:55 am
Location: Safety Harbor

Re: M1A bolt holdback issue

Post by flcracker » Thu Jan 04, 2018 5:55 am

No, the Smith Ent. extended bolt stop is extended on the outside so that it's easier to hit and release in a rapid reload situation.

Start with USGI mags and see if the problem resolves itself.

Clean the engaging surfaces of the bolt stop and the bolt. Inspect bolt for wear at the critical point where they engage each other.

Then, call Springfield. They offer a lifetime warranty on M1As for a reason. Use it.
and some rin up hill and down dale, knapping the chucky stanes to pieces wi' hammers, like sae mony road-makers run daft - they say it is to see how the warld was made!

User avatar
GunnyHiway
Life Member
Life Member
Posts: 1810
Joined: Wed Feb 04, 2004 3:41 pm
Location: Marion County

Re: M1A bolt holdback issue

Post by GunnyHiway » Fri Jan 19, 2018 6:43 pm

I have owned 6 or 7 M1As and still have a couple left and ALL of them would release the bolt if jarred hard enough. I thought all of them were like that?

When I'm on the bench cleaning mine I stick one of the empty stripper clips in the guide and ease the bolt onto it to keep the chamber open and things safe like my fingers. [smilie=011.gif]


Gunny
/:f
The M14 does my talking !............and the 1911A1 too !


CRIMSON TIDE !!!

hurricanecharlie
Executive Member
Executive Member
Posts: 676
Joined: Mon Jan 18, 2010 7:27 pm
Location: broward county

Re: M1A bolt holdback issue

Post by hurricanecharlie » Fri Jan 19, 2018 7:32 pm

A great field expedient "repair" in my opinion.
Why didn't I think of that?
Now all i need to do is find a stripper .
Can a Mosin or Enfield (might have an old Springfield) stripper be used?
[smilie=cheers1.gif]

User avatar
GunnyHiway
Life Member
Life Member
Posts: 1810
Joined: Wed Feb 04, 2004 3:41 pm
Location: Marion County

Re: M1A bolt holdback issue

Post by GunnyHiway » Sat Jan 20, 2018 5:56 pm

hurricanecharlie wrote:
Fri Jan 19, 2018 7:32 pm
A great field expedient "repair" in my opinion.
Why didn't I think of that?
Now all i need to do is find a stripper .
Can a Mosin or Enfield (might have an old Springfield) stripper be used?
[smilie=cheers1.gif]
Not sure if the Springfield will fit, I would think it probably will due to the shell base being an '06 and the .308 has the same size base.

Send me your address in a PM and I'll send you a couple , no charge.
The M14 does my talking !............and the 1911A1 too !


CRIMSON TIDE !!!

Post Reply