Page 3 of 4

Re: Parts Kits and Projects Picture Thread!

Posted: Tue Jul 24, 2018 3:25 pm
by NorincoKid
I wish I could do a postie. Would have saved me $400 on it.

Its half MK2, half MK5. I thought as a pistol, the MK5 was better in the back. MK2 parts were cheaper so I subbed those in where I could.

Not entirely sure what needs to be done to the magazine, but I've read that they can modified for 7.62x25 Tokarev, and TOK barrels are available so swapping between 9mm and TOK should just take a barrel swap and magazine mods. Seemed neat.

Still gotta figure out what I'm going to use for a front sight, and clean up the welds. Was actually considering trying to put a small section of rail on it, for a red dot.

Re: Parts Kits and Projects Picture Thread!

Posted: Mon Jul 30, 2018 2:30 pm
by Firemedic2000
Rent is the man when it comes to his reproduction guns. I wished I lived closer to him. I really like his store and having lunch with him.

Re: Parts Kits and Projects Picture Thread!

Posted: Fri Aug 10, 2018 12:09 am
by NorincoKid
Image

Getting towards the bottom of the old AK parts bin. Need a few odds and ends, but looks like enough for another rifle. Should make a decent shooter.

Re: Parts Kits and Projects Picture Thread!

Posted: Thu Oct 18, 2018 12:49 am
by NorincoKid
Image

Re: Parts Kits and Projects Picture Thread!

Posted: Fri Oct 26, 2018 12:38 am
by JonathanW
NorincoKid wrote:
Wed Jul 18, 2018 5:01 pm
Image

Do you still have this parts kit?

If you have a chance, can you take the dimensions of the length, width and height of the bolt?

Thank you

Re: Parts Kits and Projects Picture Thread!

Posted: Fri Oct 26, 2018 2:52 am
by NorincoKid
JonathanW wrote:
Fri Oct 26, 2018 12:38 am
If you have a chance, can you take the dimensions of the length, width and height of the bolt?
I do not, I got out of building them, but I do have a few functioning UZI's on hand here. I can measure in the AM

If you need to borrow a Semi bolt to copy for a build just let me know, the firing pin is a bitch to drill...if you go that route I'd anneal it first.

Re: Parts Kits and Projects Picture Thread!

Posted: Fri Oct 26, 2018 8:34 am
by JonathanW
I was thinking about if I can use the steel receiver and lower from I high end airsoft clone to build a 9mm L85 using uzi and Ar parts

Image

I was curious if the bolt would fit inside before I buy parts

Re: Parts Kits and Projects Picture Thread!

Posted: Fri Oct 26, 2018 9:56 am
by NorincoKid
Sorry they are rough and I don't have a mic, my camera kinda sucks (old phone) but this should give you a rough idea.

Image

Image

Image

and some random UZI porn;

Image

Image


Neat idea on using the airsoft as a body. I had a airsoft MP5 with a Ruger 10/22 jammed inside of it, was neat. I have a PPSH-43 here I welded it up and planned to try to fit a .22 rifle inside for a cheap WW2 plinker.

Re: Parts Kits and Projects Picture Thread!

Posted: Sun Oct 28, 2018 8:08 am
by NorincoKid
Finishing up... Still have to convert the trigger pack on the green one but the bulk of the work is done;

Image

\

Image


.

Re: Parts Kits and Projects Picture Thread!

Posted: Tue Nov 06, 2018 4:30 pm
by NorincoKid
Image

Trigger pack converted to semi auto