My Beretta with suppressor

Machine guns, SBRs, SBSs, suppressors, destructive devices, AOW (any other weapon)
Post Reply
User avatar
handlebar
Executive Member
Executive Member
Posts: 557
Joined: Tue Jan 16, 2007 9:17 pm
Location: Boca Raton, FL

My Beretta with suppressor

Post by handlebar » Wed Aug 17, 2016 8:03 pm

Had the barrel threaded and put on the suppressor.

Image
Last edited by handlebar on Wed Aug 24, 2016 6:03 am, edited 1 time in total.
Handlebar

User avatar
870Mike
Life Member
Life Member
Posts: 4654
Joined: Wed Apr 24, 2013 6:32 pm
Location: Broward (Da 'Hood)

Re: My Beretta with suppressor

Post by 870Mike » Wed Aug 17, 2016 9:32 pm

Shot it yet? Quiet?
"Send lawyers & money...have enough guns." - 870Mike

User avatar
cvasqu03
Life Member
Life Member
Posts: 1143
Joined: Thu Feb 02, 2006 11:19 pm
Location: Miami, FL

Re: My Beretta with suppressor

Post by cvasqu03 » Wed Aug 17, 2016 11:28 pm

Nice. Are you going to raise the sights?
If you're going to knock a man down, do it so he can't get up.

User avatar
handlebar
Executive Member
Executive Member
Posts: 557
Joined: Tue Jan 16, 2007 9:17 pm
Location: Boca Raton, FL

Re: My Beretta with suppressor

Post by handlebar » Thu Aug 18, 2016 4:53 am

I have shot it on my SBR, but not on the Beretta, yet. On the SBR, it is very quiet. The sights are a tad low. I am trying to figure that one out. I have marked the suppressor where the sights land with a white dot. This may give me an aim point, otherwise, a spot of epoxy may work. Any suggestions.
Handlebar

better2have&notneed
Contributor
Contributor
Posts: 1130
Joined: Sun May 31, 2009 3:31 pm
Location: Summerfield, FL

Re: My Beretta with suppressor

Post by better2have&notneed » Thu Aug 18, 2016 6:42 am

Looks great!

I thought about higher sights on my pistols, but after shooting them with the cans on I found I didn't really need them. Try shooting it a few times and then decide if you want different sights.

John K
Administrator
Administrator
Posts: 578
Joined: Sun Feb 06, 2011 12:33 am
Location: Ft. Lauderdale

Re: My Beretta with suppressor

Post by John K » Thu Aug 18, 2016 12:47 pm

better2have&notneed wrote:Looks great!

I thought about higher sights on my pistols, but after shooting them with the cans on I found I didn't really need them. Try shooting it a few times and then decide if you want different sights.
+1 A good NPA, and shooting "through" the suppressor take some time to get used to.

User avatar
Big_Mike
Life Member
Life Member
Posts: 4198
Joined: Mon Jul 27, 2009 2:03 pm
Location: Orlando, Florida

Re: My Beretta with suppressor

Post by Big_Mike » Thu Aug 18, 2016 1:34 pm

handlebar wrote:I have shot it on my SBR, but not on the Beretta, yet. On the SBR, it is very quiet. The sights are a tad low. I am trying to figure that one out. I have marked the suppressor where the sights land with a white dot. This may give me an aim point, otherwise, a spot of epoxy may work. Any suggestions.
I would think these sights should do it, dovetail rear replacement and slip over front sight.

http://www.midwayusa.com/product/323340 ... teel-3-dot

Image
Deo Favente Perennis.

dys·gen·ic [ dis jénnik ] - 1.detrimental to future generations: affecting later generations detrimentally by passing on undesirable characteristics

Post Reply