12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Over/Unders, Doubles, Pumps, Semis, Home Defense.
hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Sat Nov 03, 2012 8:21 pm

Here is breach picture of that 12ga O/U made by Armi-Lumar
It has the bottom barrel rifled right from factory, top barrel smooth,
with interchangeble chokes. A real neat gun.

Image

Good news, I got few samples of first production run of my 585HE
cases from Bertram, to test for strength and measure for uniformity.
They all measure perfect and especially the belt length headspace.
He made part of the run, a 1000, without headstamp..And over 3000
with headstamp. Cases only 3 bucks each if you get in on the first
shipment right away..Ship by mail to US cost too much, $1.50 each,
so we will have a bulk freight shipment to US as big as possible.
Folks in other countries order direct from Bertram.

This case can be used in different style guns.,
Bolt, Falling blocks, Break actions, Etc. I have reamers, and dies.
Manson Reamer can make more reamers,CH4D has dies also.
Earlier in thread I've shown various 585HE guns we have set up. Here
is a break action, with 585 barrel monoblocked in, one my favorites,
we just got done.

Image


I tested 585HE moderate loads(650gr @ 2400) in NEF, CBC, Pedretti,
etc, break actions and didn't need sizing on the bottom 2/3. Real
tough built cases. Cases, are real uniform. For high test loads we
fired couple with 650gr at 3000 in Enfield bolt action, and it extracted
ok, and resized ok back to specs. About a 62k psi load. Pockets tight.

First picture, shown is some he made without headstamp that I stamped,
and some with stamp and ones I made on the right..
Also they can be used for wildcats, shorter cases, etc, and folks can stamp
what they want. 2nd picture you see them in a regular # 31 shellholder,
they don't need a special holder.

In 3rd picture of sectioned cases, you can see how strong the cases are
in base and corners, strong like the ones I made, on the left in picture,
which were real strong cases, that worked great with max loads..
The new 585 from Bertram on the right in picture.Nice strong base/corners.
He supplies same base cases for 408 Cheytac, used with hot sniper loads
that run real high average pressures..He will be manufacturing
these Cheytac runs regular, so we can get ours made anytime
we get money built up for an order..Ed



Image

Image

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Mon Nov 19, 2012 1:13 am

Here is overall view of the Armi-Lumar O/U 12ga that has
one barrel rifled. Second is another view of the breach.
Nice looking gun.

Image

Image

Here is picture of the 58cal Minie bullets in 20ga BPI Commander
shotcup wads, and some 50cal bullets in 20ga BPI Sport shotcups.
Sport wads were too small inside and to tapered inside for 58 cal.
Other two are 458 bullets in a non-discarding base that had SPW,
Buckhamer type slugs in them, that someone took apart, that I got.
And one 100yd group shot by Ajay on ShotgunWorld with Sav 220
20ga, with 20ga Commander wad and 58cal cast Minie bullets
measured about 2 inches. Four shots in two inches.Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Thu Dec 06, 2012 4:26 am

First is picture of the 8ga Falling Block with texturized paint finish
on the stock. It enhances the grip quite a bit on hard recoil guns.

Image

Second is the Greener that I have my 585 HE in.Also have
12ga barrel for it..

Image

Third is Magtech singleshot action that I'm experimenting
with putting on a thumbhole stock.

Image

Fourth are the long bmg bulleted blank cases that I found, to use to
make my 700HE Long case, 4.27" long. I have few extra sets of
five in links like shown, extra to sell 5 at a time in links,
if some need them for their collections, etc... Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Wed Jan 02, 2013 2:34 pm

In our research to find economical and easy to use setups to load
various slug/sabot combos in 12, 20 and other gauges, you've
seen what we are doing with 58cal slugs in 12ga accutip type sabot we
are getting built, and 58cal slugs in 20ga BPI Commander shotwad.
You've seen pics of group shot by Ajay 58cal in 20ga Commander wad.
And Greg Sappington made 16ga HP slug that fit 12ga BPI CSD wad.
CSD wads are little thicker. In that vein we found another 20 ga combo
that uses the BPI 20ga CSD wads and larger diameter of the 54cal
muzzleloading slugs. Wad is thick and short so we can get the
volumne of our slow powder we want in the loads for higher speeds.
And base of CSD 20ga wad is thicker and stronger than most wads.
. It doesn't have built on cushion, doesn't need cushion, which is not
needed for slow powder loads. Has a good built on powder seal.
It is long so it can be cut to fit any 54cal slug length.
Best 54cal slugs to use are .543" and up.
There is .548" Sharps style 2nd in picture from Dixie Gunworks.There is
54cal Great Plains in picture on left, Far right in picture is 550 Magnum
jacketed bullets in 20ga CSD. Great for hogs, bear. There are a variety
of 54cal slugs you can cast or buy. Not big number like 58cal, but enough
to find good simple combo. Shot 3" group with 54cal Great Plains in
CSD at 30 yds, smooth bore. 380gr going over 2000 fps.
Second picture shows they even work and fit good in 20ga RMC brass.
Fits in a brass case real tight with .548" Sharps style slug in picture..

Image

Image

Third picture shows how we mono-block 585HE barrels into strong
singleshot break actions. Done it in NEFs, CBCs, Pedretti, Beretta,
and the Magtech 199 shown above.

Image

Fourth picture is the O/U Tristar with 585HE on top and 3.5" 12ga bottom.
We sleeved the top barrel with .585" ID sleeve. We will use it with
the 58cal .585" Minie hollowbase slugs. Bottom just for shot loads
with a interchangeable chokes. Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Tue Jan 15, 2013 1:35 am

Little work on non-discarding 12ga sabots,You can get SPW
wads without slugs in them and we set up one for a light load.
We put a 20ga Lyman in some and they stay together ok. Just
shorten the bottom skirt of Lyman and bevel the bottom corner.
Total weight sabot and all is 360gr,,Shown In the picture..
We also shrunk the skirt of the 12ga Lyman cast slug and put it
in 12ga SPW wads and total about 550gr. If you have Lyman
12ga mold, can use it as pattern to make a slug to go into a
SPW wad. Leave the top part same as original Lyman and make
bottom so it fits in the SPW with real tight fit.

Image

I like to use P14/M17 Enfields for our testing. Great for my 585HE
case and in picture it shows how we change the sear spring to one
on the back of the sear. So we can open up the bottom to feed
the long cases from singlestack magazine box by removing the
unneeded front of the sear and metal above it in the bottom, giving
room to the back, for cases that are 3.9" plus overall loaded length.

Image

Couple guys who are setting up 585HEs in singleshots are going
to shoot 58cal Minies and other bullets and use black powder
and/or substitutes. So I tested some with Pyrodex pellets,
Used 54cal, 60gr equivalent and they stack in the case ok,
and just beveled corner of bottom one so it set tight to the base.
As the case has good inside radius. Used 3 pellets with 24ga
card over pellets, 3/8" felt wad and another card with 440gr Minie.
There is a certain nostalgia about all that sulfur smell.If you can
stand the cleaning. Slug going 2100.. 4 pellets about 2400.

Here is picture of another long bullet in sabot/wad , in 12ga that
was sent to me. Ajay on Shotgun World put these together.

Image

Did some testing, 12ga plastic & brass with new super slow RE-33 powder.
It fires off ok in 12ga with 700gr and heavier slugs, with shotgun primers
like RE-17 which is much slower than shotgun powders. .
It is made the same way as RE-17 as far as how the rate of burn
deterrent is put into the powder. Which is why it ignites in large diameter
cases like 12ga and BMG with shotgun primers. Really be great for super
heavy 1100 to 1500 grain slugs to get good speed and keep case damaging
peak pressures down. Example in 3.5" Fiocchi 12ga plastic case, 690gr slug in
BPI Helix Driver Wad with 180 gr RE-33 the basecup only expanded .002".
And they are thinner basecup than some..Ed

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Thu Jan 31, 2013 5:08 am

Last picture above shows what can be with sabots. It was thought to
be 20ga size when we got picture, but it is a smaller
45cal caliber sabot with 30cal streamlined bullets in them.
This was set up by the poster 'edge' on Castbullets forum.

More info on the SPW sabots with 520 gr Lyman reworked and locked into
them. With 3.5" brass RMC in the NEF long barrel gun, going about 2500
they smash though 6" timber with Lyman tearing wood up. Also got the same
combo 2200 in 3.5" plastic. Lyman in sabot on the left in picture on
right is factory SPW.

Image

Another setup using the largest diameter 58 Minie I have is this .590" in this
12ga real thick muzzleloading wadcup for steel shot. I chamferred the bottom of
Minie slug and wedged it in the cup. The cup comes real long and we cut it off.
That leaves perfect edge to roll crimp against. Dab of epoxy holds the Minie slug
in, so it works like a non-discarding sabot. This wad has is own seal and fairly
short compared to others, so it leaves room for more of our slower powders.
Shorter slug and wad setups make loading easier.



Image

Here is picture of the Magtech we redid in the 585HE by mono-blocking in 585
barrel. This is second one we've done. Tried out a ladder peep sight on the
back. Makes a neat gun.That underlever is a great touch.Ed


Image

As part of the 585 test guns have smooth barrels, they are like a hopped up
24ga. We got couple bags of 24ga cards and felt wads. Easy way to use
reduced loads as the wads are perfect in 585 case. For comparison top load
say with RE17 and 650gr bullet is 170gr, but you can put in 100gr and card
and couple wads and have real easy load. And you don't have to worry about
airspace. Great for reduced loads with Minie slugs. In the same vein you
can put in a card over the powder and about 3/4 oz of shot and have a real
speedy 24ga shot load equivalent. Put card over the shot and glue it in.Ed

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Tue Feb 26, 2013 10:33 pm

First picture is of a nice finished 87 Winchester Will Sanders got set up
and he is using short brass cases.Beautiful scroll work on the stock.

Image

Next is takeoff of a slug idea from Longbow on Cast Boolits, 12ga lead
roundball with section copper tube, wads compressed inside, BPGS seal on
bottom, screwed together. I have many boxes of wads. Now he did his with
screw into ball, put tube on with screw centered inside tube and filled tube
with hot glue. It stays together. Both are nose heavy for smooth bore work.

Image

Next is side sectioned view, one of our 585HE cases, showing how 3/4
ounce of shot fits in.. 585 is same bore as 24ga. Cards shown are 24ga.
Just glue top card in. Some of our 585s are smoothbore and the HB Minie
slugs work at short range and the shot will do at short range also going
about 2000 fps. Could use 24ga shotcup.

Image

Next, Mossy 390 bolt action, with heavy 585 barrel. Makes a nice big bore gun,
and handles nice with texturized stock finish. About same strength as
the heavy break actions I have 585HE in.Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Sun Mar 17, 2013 3:01 am

Here is picture of the 12ga short brass RMC cases being used in
the 1887 WIN shown above. They are 2 5/8" long cases and we
get 600gr over 1900. He had work done on action to get it to feed
these and 3" roll crimped plastic. Brass loaded about same length
as 3' plastic crimped little long.

Image

Next pic are Lyman slugs cast for thin 12ga wad, used in thickwall
10ga VP100 wads. These Lymans I got are on large size and fit
VP100 fairly well. Makes easy, lighter, superfast load in 10ga.

Image

Next; further idea with Longbow's tube/roundball slug shown above.
Use tube hot glued to ball with screw in the back and use it in
a 10ga VP100 wadcup. These type slugs little more accurate used
in wads as opposed to fullbore.

Image

Next shows picture of a long 585 bullets, about 1600gr in our 585HE
cases. Got the idea from Bret In Minn that could setup 585HE
guns with super long throat and load down to subsonic speeds to
make the 585HE Whisper.....And regular bullet loads would still fire
in the same guns......And at subsonic 1050fps it would have about
4000 ft lbs, about twice what the peashooter whisper cases have.
And my case could get a 2400 gr long bullet to same subsonic speed
for 6000 ft lbs. And one that long would have proportions like the
newer tank cannon, smooth barrel saboted darts, that it could be
possibly be done, using long 2400gr in smooth barrel.
Neat ideas from guys interested in whisper type loads.

Image

Last is picture of FBW in our 585HE with handgrip stock and light
barrel for lightweight carrying. Grip is weighted, gun is 6lbs.
Barrel is 28". I'm not a fan of light barrels. 650gr at 2500 is max of
what I can hold onto shooting from the hip Moderate load
.Little info about my 585 loads, like in the break actions and the
Mossy in post above. I load about 85% max velocities, but to get
85% we only need 2/3 the peak pressure, like 40,000 psi
instead of 65,000...Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Fri Mar 29, 2013 2:14 am

We have a winner it seems. The 12ga sabots using 58cal slugs.

Image

The sample 12ga sabots got here earlier this week. And we got a bunch
of testing already for opening and sealing, and some accuracy testing .440gr
Minie bullet, measuring .575"; with OD of sabot with slug in it of .737" It is
perfect. Going moderate 1800. Petals opened perfect and evenly and they all
stayed on perfect. No petals twisted or torn. Tested in 3" case with slower
powder loads. 80gr of 4759 and 50gr Alliant Steel. Fiocchi case.
Savage 210 rifled barrel, 1 to 35 twist. Cases with slower powders expanded
only a little, and those cases are soft ones.
We have big bunch of the sabots here now.


Image

All petals were opened at about 30 deg to the base when picked up.
With ither powder the bases have no damage, or burn throughs or melting.
Took rifling perfect, so skidding on the rifling. Most of the rifling grip is on the
bottom half of sabot, which is why these and Accutips are best as the bottom
is full size instead of dropping back in size, compared to the top, like many
other sabots. Rifling in the barrel still clean..

Image

The Minies are hollow based and the slug edges did not cut into the inside of the
sabot bases,just a slight impression. We have got good base thickness.
Good Accuracy - In the cold and very windy day, hit milk jugs at 30 yds.
Here is picture inside sabot showing just a slight indent. No need of cards under
slugs, and if you did, the the slugs would set up in sabot and not have the
curve of the slug behind the inside circular rib for best fit...

You got to use right powders. With right slower powders( not fast shotgun),
that start easier and used in larger amounts, you won't tear up the sabots.
It is false economy to use all fast shotgun powders,trying to get twice as many
shots per pound... and tear up sabots, expand cases too much, get poor groups,
miss that deer or whatever. For most of you in 3" cases Alliant Steel is best.

Get with me for sabots -- gunowner at journey.com Ph- 1-989-644-5228
THE undersize blue ones sold elsewhere for 34 bucks a hundred plus postage.
Ours are 33 bucks per 100 postage included, or $20 for 50 postage included,
with a bonus WE WILL send along 10 slugs with 100 order, 5 with 50 order.
to show you what to get and to test with. Slugs can be 440gr or 500gr..Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Sat Mar 30, 2013 5:41 pm

Here is picture of a bunch of the sabots with different slugs and bullets.
Back Row- Two roundball load, balls 285gr each-- pointed long 700 gr -- a blunt
solid 700gr-- tungsten slug 1000gr --- jacketed bullet -- 600gr.
2nd row-611 Lyman 530gr Minie- 500gr flat base- Lee 500gr hard--Lee 500gr soft
1st Row- Lyman 440gr old style minie-- Lyman 510 gr new style-- 440gr from Dixie
Gunworks-- 400gr Lee target style. I like 440gr old style and 440 gr Dixie. For sale
on Gunbroker is all sizes and weights.. Or cast your own. Lots of moulds around.
Lee moulds only 20 bucks. Best diameters to use are .574 " to .577" Minies.
If you have ones bigger and they are not hardened you can roll them betweem two
hard surfaces and they will get little smaller. I have some that are .585" 440gr
and work in my 585HE and they can be rolled smaller.

Image

Here are sabots with variety of seals/wads, and the shortest one in picture with
white felt wad just fits in 3" case with 80gr 4759, and still leaves room to roll crimp.
I compress it in hard. Now only faster powder than 4759 I'd use is Alliant Steel in
smaller amounts, 50gr Steel, in 3", and thicker wads and cushions like shown.
To roll crimp over the top edge of sabot we had .220" of case before crimping.
You only have to crimp top edge of sabot real good.


Image

After crimping the slugs are tight and don't move around. The circular rib inside the
sabot holds slugs tight back into the base. Speeds over 2000 fps
will be gotten using 3.5" plastic cases, with our slower powder loads. .
More testing for accuracy yesterday, a warmer, calmer day, with steel sights.
Hit. paper plate at 50 yds.

As said above, best to use right powders. Right slower powders( not fast shotgun),
that get to peak pressure slower, thus can use larger amounts, can get to higher
velocities, and you won't tear up the sabots and won't expand cases as much.

For most of you in 2.75" and 3" cases Alliant Steel is best.
FOR 440GR SLUGS IN SABOT---For 2.75" start at 40gr and go up to about 50.
For 3" start at 45gr go up to about 55. I like 3.5" best as you can load much easier
for speed, still have more cushion wads. Start with 50gr Steel, go up to about 62.
Case brands act different, but using the slower powders minimizes the differences
and keeps us away from surprizing pressure problems.

In 3" plastic,most 4759 I can get in and still have 1/4"cushion is 80gr.... In the 3.5"
I can get in 105 gr with this sabot and get over 2000 fps, In these loads if using
480-500gr cut back 3 gr. These 58cal slugs can be cast or they are at Dixie Gunworks
and 4 guys on Gunbroker got them. Get ones .574" to .577"


Interested in sabots--- gunowner at journey.com Ph- 1-989-644-5228
THE undersize blue ones sold elsewhere for 34 bucks a hundred plus postage.
Ours are 33 bucks per 100 postage included.
Or $20 for 50 postage included..
.Or 150 for $45 postage included----- ALL with a bonus
WE WILL send along 10 slugs with 100 order, 5 with 50 order. 15 with 150 order.
to show you what to get and to test with. Slugs can be 440gr or 500gr......Ed

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Thu Apr 04, 2013 10:49 pm

Here is picture of 45-50yd target, used a scoped NEF Ultra, the sabot load of a 440gr
58cal slug in it at 1800... Measures 2.5" on outside for 3 shots.

Image

Here is pic of almost 2100 of them. More coming. Time to
get them and get loads working.

Image

And A little funnin humor for us big bore nuts..Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Tue Apr 09, 2013 8:24 pm

Some more info about our sabots and various slug weights......
First and most important is our sabots fitting real tight like the Accutip
Sabots, they will not get the same speed at the same pressures as
the undersize grey and blue ones, But they do leave the barrel
headed straighter and without damage, even with hollowbase 58cal
slugs in them as the pics above show. No cards under slugs in sabots.,
But with good powder seals, using Alliant Steel, and good 1/4" minimum
cushion wads.

The 440gr Minie slug of .575" in the 3" cases is the one I used as a
base loading, to work each way by weight to find what loads of
Alliant Steel work and extract in my NEF. Using 3" soft base cases.
Here is pic of before/after of Fiocchi cases, on right unfired and left
fired, 55gr Steel with 440 gr slug.

Image

For 440gr max of 55gr Steel
For 400gr max of 57gr Steel
For 360gr max of 59gr Steel

For 490gr max of 52gr Steel.
For 510gr max of 49gr Steel
For 540gr max of 47gr Steel.

I tested all these weights for extraction. It is real nice to reach into a
bucket, grap a sabot that fits right, and go to loading and shooting.
Many of you need to get in on the fun.
Here is picture of Fiocchi with sabot, roll crimped. The top of sabot is
perfect for roll crimping...It is setting under crimp tool in drill press.

Image

Earler I showed the 585HE Falling block with pistol grip and the light
barrel. Here it is with Knoxx Compstock buttstock. We added 2 extra
springs inside for relatively hard recoiling gun, as stock originally made
for a REM 870 Pump. Works great and looks nice; will putting one on
the Magtech 585HE singleshot break action and got one in rifle stock
for Ruger 77 in 585HE.

Image

And many guys want wildcats with shoulders, with big neck down, so
in developing the ultimate 700 blaster, here is the 700HSM. Shown next
to Gibbs 650gr ball powder..1000gr at 3800...How about that.
Will be one of only 2 guns I plan on being over 30 lbs, other is 2bore..
Whoppee.....Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Mon May 06, 2013 9:59 pm

The sabots work in brass cases .First is sabot in a Magtech brass case,
next to 3" plastic.. In shorter brass it would hold about as much powder
as in longer plastic if loaded like in the picture..
Sabots are about .734-735" with slugs in them, and
the Magtech brass with its thin sides still is slightly small OD at the
top compared to plastic, with sabot wedged in.

Image

Next is sabot in RMC case, and sides are full thickness like plastic cases
at the mouth, so don't expand case to hold sabot. We have RMC make case
mouth ID to fit sabot. Sabot being little over fits barrels tight and rifling
impresses into plastic well and gets best spin, and being tight it leaves barrel
straight, with petals opening evenly. Brass case mouths are tight enough that
we push sabot in with a press.Saves trying to crimp heavy RMC case.

Image

Here is picture of a barrel and barrel on a gun from 20 gauge singlshots that
will have the heavy 20ga rifled barrel in picture, mono-blocked into them.

Image


The sabots are not moving very fast and I need money out of them asap, an
emergency bill coming... And seeing as how we're low on slugs to send with
the sabots, in big numbers, and no one has yet to buy out our stash of sabots,
and set up so they can be selling the sabots, we will try selling them
fast in next few weeks . So we will be having a sale on just the sabots, in larger
amounts only. We will send one each of 440gr and 500gr slug so the guys
can see what we have found that works.
Because of the shipping costs and boxes that 2, 3, or 4 bags of sabots fit
in, that have an affordable postage cost to pay,we will sell these in 200,
300, and 400 size orders..So, 200 sabots $47 Shipping included,
300 sabots $65 Shipping included...400 for $83 shipping included.
Now 200 of the other brand X of undersize ones cost $68 plus shipping.
There was dozens of guys the last few years all over the internet that bought
undersize junk, that wanted good sabots, and complained that the ones they
bought elsewhere didn't work......We haven't heard from most of them, So guys
see if you got time, please help us out here..And setup for good shooting...Ed

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Sun May 26, 2013 4:51 pm

What causes sabot problems/inaccuracy. Some pictures will help.
First 2 shows a skinny post that pushes on a cushion or sabot
bottom and it can bend or deflect which if that way when exiting
barrel can start sabot or slug crooked.

Image

Image

And more important item that can cause lack of accuracy is if
base of discarding sabot tapers or steps down so that it isn't real
tight as it leaves bore, which can allow it to be cocked.
On the left is our sabot which has base right and other brand
which tapers a bit. Easy to see.

Image

Next is a ball and slug load in 2 of our sabots. A 285gr .575" ball
flattened, put in the bottom and 400gr Minie above, two different
styles of Minies.

Image

Here is couple 16ga discarding sabots I made from the undersize
12ga grey ones. Didn't have to take off much. Much better use
for them. I made them, after Paul in Alaska asked about
where to find 16ga ones, to see what they looked like.
They still use 50cal slug.. Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Sat Jun 22, 2013 3:31 pm

Here is 16ga discarding sabots made from grey ones with other 16ga slugs..
20 ga factory sabot on left for comparison.

Image

Here is picture of 12ga wads showing good and bad support to the
bottom of the slug.If in part of the loads the support gets cocked, then
the slug won't be straight on and can account for open groups.

Image

Here are 2 sabots on the right with super heavy tungsten slug. It is 1100gr,
but tungsten costs ten times what lead costs.

Image

Here is a sabot home defense or close range defense load setup using our
sabot. It has five flattened 45cal balls in it. Flattened into a fat disc weighing
145gr each. You'd star crimp it or use card over them and roll crimp. Like
having a bunch of supersize flat buckshot, only super size.

Image

Here is comparison picture of the 58cal slugs used in our 12ga sabots, with the
puny slugs used in many other sabots. And we've moved 5500 of the sabots.
Deer season is coming fast. Maybe time to get loads tested/sighted in is now.

Image

Some more figures. The 24hr Campfire forums is first one, with our 12ga FH thread,
to get over half million thread views.The HighRoad second.
TheFiringLine, third. AccReloading fourth...Ed

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Sat Jul 06, 2013 12:14 am

We have moved few thousand sabots.More here.
Here is picture of an 8ga wad with tube slug in it, we made.

Image

A pallet load of our 585HE cases has arrived in the US
and will be here in little while. And should be another pallet
of them this fall. Here is picture of our 585
with the solid turned CEB bullets in them.

Image

Here is some helpful, simple math to help figure out the kinetic energy
of your loads, just by having bullet weight and speed.
Just put these multipliers which are used for each speed, on a list
and multiply by the bullet weight in grains. Fast and easy.Ed

Speed..Multiplier
1500------5
1600------5.7
1700------6.42
1800------7.2
1900------8
2000------9
2100------9.8
2200------10.75
2300------11.75
2400------12.8
2500------13.9
2600------15
2700------16.2
2800------17.4
2900------18.7
3000------20

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Thu Jul 18, 2013 6:15 pm

Here is picture of current 58cal slug options that
you can get molds for from Lyman,
Just make sure they are .574" to .577" diameter,
the best size for the 12ga sabots.

Image


A barrel of 585HE cases..Ed

Image

Made by Bertram and I tested them to max loads and cases hardly expanded,
650gr over 3000 fps. The same draws used by him to make high pressure
Cheytac cases, and to finish mine just uses belted header and cases left
straight and trimmed longer.He makes tens of thousands Cheytac steady all
the time now and can make ours steady also when needed.....Ed

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Wed Aug 21, 2013 4:17 pm

One of our sabot testers with tight barrel, 12ga Abolt, with wide lands in
the barrel, who couldn't do any good at all with our sabot and Alliant Steel
and one type of slug, had to go to IMR 4759 & different slug.
It would twist up the sabot petals. Terrible accuracy.

My guns have NEF/Sav size barrels and worked fine with Steel as well as 4759.
Petals open perfect here. The Abolt barrel about .005" smaller than NEF/Sav and
the lands over twice as wide as the NEF. And has real narrow grooves.
Guys with Nefs say sabots open fine like ours here.

He went to different Minie slug and our slow powder loads using
IMR 4759 powder up to 78-79 gr and finally got down to 2.5" group, I told him
go to max which is about 80-82 in 3" case.That barrel is like a lot of
EU made barrels and many are replacement or add on barrels in many slug guns,
and that is reason why it is so hard to get accuracy across the board in
sabot shooting in all guns--Takes a lot of work.. Another tester with NEF 12ga using
Alliant Steel with sabots got good groups like we did here. I tell guys if
problems occur go to 4759.

What was happening to sabot petals in the barrel, with the extra tight fit and
wide lands were petals twisting.. The wide lands were not cutting into the base of
sabot like in NEF/Sav210 barrels. The twist effect of rifling was on the surface
of petals, twisting them. It was not getting good hold on the sabot body. The
4759 starting slower allowed the sabot to get its spin started up to speed
with the wide land rifling and narrow grooves..It is just the opposite of
way NEF/Sav 12ga barrels are done. with narrow lands which impress into
the sabot base the way it is supposed to work..I showed pics above of the
good rifling marks impressed into our sabots.

I think after this experimenting run I feel that a lot of accuracy problems
across the spectrum of barrels are due to barrel differences, and not just
the differences in factory slugs and/or reloading components.

Here is pic of bag of our 585 cases with plain head if some need them for
wildcatting.We have quite a few. Fifteen have 585HE cases now. 585 gun
building is accelerating. We can get folks going with 100 cases, dies, and soon
a barrel; and shipping, for 750...Ed

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Sun Sep 15, 2013 4:18 pm

Here is picture of our 12ga sabots with the marks that the barrel lands made, marked with
black marker. The one with narrow mark is Savage barrel and one with wide mark is
an Abolt barrel. And the ones fired in Savage and NEFs with the narrow lands the marks
impressed into the plastic getting good bite and not twisting the petals. The one from abolt
he used slower powder for easier start and it open petals ok, without twisting petals like
the faster powder did for him.

Image
..
Next is picture showing top edge of sabots. Our sabot on left you roll crimp down over
the inside of it a little . We have lots of them yet.
The other factory sabot they crimp real short and sharp
180 degree crimp down on top of it.

Image

We see a use for modified 585 application in Indiana deer hunting. Mainly shotgun only, but
they also allow rifles with over 35cal pistol calibers; and any over 35cal rifle with a case
1.8" or shorter, usually short wildcats. So we have the the 585 HI... The I is for Indiana.
Here is picture of it next to the kinda little 500 S&W. 585 HI holds over 80 gr powder.

Next picture is a Magtech chambered for it. Gets 440gr Minie over 2,100 fps.
The .585"- .587" Minies of 440gr, 540gr, etc work in it, and they're good deer slugs
We got other guns with it going into; bolt guns, like in the last picture,
single shots and checking couple lever actions.
Might work great in MNs many guys like....Ed

Image

Image

Image

hubel585
Member
Member
Posts: 138
Joined: Sun Nov 27, 2011 2:42 am

Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

Post by hubel585 » Wed Oct 16, 2013 3:06 am

In above post we compare the top thickness of sabots
.Here is comparison of the thickness of the sides of two types of
brass 12ga cases, the RMC turned case and the thinner
Magtech drawn case. Easy to see you can't size with same dies
and sometimes you have to use different wads..

Image

In posts earler in the thread you saw variety of wad columns with
12ga sabots and here is picture of my favorite wads to go between
seal and sabot. The white felt ones from BPI. They compress down
evenly on firing, easy to load, decent price,

Image

You've seen the work on our 585HE posted. Folks ask what case
I made first ones from and how. Here is a sketch showing the steps
I used to make the first 585HE from long basic straight Nyati brass.
The start of the belt step I put on the case where it is thick I do it
in my case spinner lathe I made. Then case is lubed and run into
couple swaging/sizing dies and comes out formed into our belted,
straight sided, 585HE case...... It is really faster getting a big
run of cases made in a factory.


Image

Shot a 12ga sabot load w/440 gr Minie bullet in smoothbore Rossi
in 3" case, Going about 1700... .. 4" group 3 shots at 30 yds.
Gun works fine, shoots nice. Got extra weight in the butt.
The Minie I used is a semi-round nose. If I had the ones of same length
with blunt nose, slightly heavier the group size would be smaller as
they'd be more nose heavy, be like Foster slugs..Ed

Post Reply